MSD

The Street Fire Ignition offers capacitive discharge technology and will fire a series of multiple sparks that last for 20° of crankshaft rotation when the engine is running at lower rpm. This...

The Digital 6A wiring is routed out one end of the unit through a sealed and locking connector. This eases installation and keeps your wiring looking neat and clean. The Digital 6A are supplied with...

The 6AL Ignition Control wiring is routed out one end of the unit through a sealed and locking connector. This eases installation and keeps your wiring looking neat and clean. The built-in rev...

This Spark Plug Wire Sync Kit installs to the number one spark plug wire and senses the trigger signal and sends this information to the Ignition through a fiber optic cable. Features:• For...

This Shielded Magnetic Pick-Up Cable will help protect the trigger signal from the distributor or crank trigger pick-up from Electro Magnetic Interference. The pick-up wires are wound together and...

This RPM-Activated Switch will perform a variety of different functions from turning on a bulb or solenoid to activating an MSD Timing Control at a desired rpm.The RPM-Activated Switch, has two...

The MSD Pro Power Coil is designed short duration applications such as drag racing. Features:• High voltage coil designed for short duration applications only• Primary and secondary...

The Power Grid Manual Launch Control Module allows you to make quick, last minute changes. Perfect for those who use a 2-Step rev limiter! • Ability for easy, last second changes• Change...

MSD’s Non-Magnetic Pick-Ups are engineered for extreme applications. This Pick-Up was designed and tested on 300+ mph top fuel dragsters! 

The Programmable Digital-7 Plus Ignition includes all of the standard programmable features such as Individual Cylinder Management, Step Retards, Rev Limits, and Shift Points. A MAP sensor is...

The Power Grid Harness Adapter allows you to use your Digital-7 Programmable to install a Power Grid Controller with very little alterations. The harnesses are direct plug-ins for existing wires, but...

This Power Grid replacement wiring harness is designed for use with the MSD-7730 Power Grid Controller.

This Advance RPM Control Module sets rpm limits based on rpm acceleration or time since launch. Features:• Plugs into CAN-Bus Bridge• Use with Power Grid Controller• 4-Connector...

The Power Grid Ignition System is the next evolution of our Programmable 7-Series Ignition Controls. The Grid incorporates an efficient 32 bit microcontroller and an all new software program, called...

The 7AL-3 allows you to make adjustments any time you want. It packs high voltage with four step retards, three rev limits and an rpm switch. All of the features are adjusted using plug-in modules...

You’ll recognize the 7AL-2 Plus Ignition Control, as its predecessor is the most popular ignition control used in drag racing. The “Plus” model updates the original 7AL-2 with...

This Launch Rev Limiter Switch Box, also known as a Manual Launch Control, lets you change the launch rpm setting of the MSD-7531 Programmable Digital-7 Plus Ignition Control when you are in the car...

The Power Grid Ignition Control is specially designed to mount to the MSD-7730 Power Grid System Controller Box. Specifications:• Current Draw: 1.3 Amp per 1,000 RPM• Primary Voltage:...

The Pro Power HVC-2 Coil is designed for racing applications with an MSD 7 or 8 Series Ignition Control. Improved voltage distribution is achieved with an iron U-Core design with a segmented bobbin...

The Pro Power HVC Coil is designed for racing applications with an MSD 7 Series Ignition Control. With a combination of extremely low primary resistance and the efficient design of an E-Core coil,...

Use this Firewall Feed-Thru to route the spark plug wire through the firewall. Features:• 1/2" insulation so the coil's spark reaches the distributor• Prevents voltage leaksClick here to...

MSD Ignition Testers save you time by allowing you to test the ignition and coil without removing them from your car! With the MSD-8998, you can check the operation of MSD's single channel ignition...

This CAN-Bus Extension Harness provides 6 feet of extra length to reach your Power Grid System.Length: 6'

This Power Grid 4-Connector Hub will allow users of the Power Grid System to connect up to four MSD accessory modules. • Also known as a 4-Connector CAN-Bus Hub• Intended for use with MSD...

This MSD Three Step Module Selector lets you choose from two or three different rpm limits that can be activated at different times. Features:• It can also be used with an MSD Timing...

This MSD Two Step Module Selector lets you choose from two different rpm limits that can be activated at different times. Features:• It can also be used with an MSD Timing Control• Launch...