FTSPARK-8, Gen II, 750mJ, PRO550/600 FTSPARK-8 Harness, Coils & Plug Kits

The FuelTech FTSPARK is an extremely high energy Capacitive Discharge Ignition (CDI) system designed to meet the highest spark requirements for racing. Developed for high horsepower combinations and tested proven on 5,000+ horsepower engines!

It is compatible with any ECU on the market! It's able to generate a spark with up to 750mJ (mJ=mili Joules) of energy and is capable of firing the spark with 140 Amps of current in the coil primary. With these features, FTSPARK generates a spark with approximately 5 times more energy and 10 times more current compared to a SparkPRO ensuring a burn in any condition, especially in extremely rich air fuel ratios.

TECHNICAL DESCRIPTION
• Programmable energy via CAN or digital input to adjust the energy level; - 475V in the primary of the coil, which helps to prevent interference in the system;
• 140A of current in the primary of the coil with Racing CDI FuelTech coil for FTSPARK 750mJ;
• CAN communication with FuelTech PowerFT ECUs for diagnostic and datalogging;
• Automotive connector with gold-plated terminals;
• Serial bus (1 wire) that allows the use of only one ECU output that triggers all ignition outputs (only with PowerFT);
• Case: Anodized Aluminum and Plastic;
• Maximum working temperature: approximately 212 F;
• Supply voltage for full power: 14-26V. Minimum voltage for starting 8V;
• Maximum operating frequency: 670 Hz;
• Compatible with other ECUs on the market. Check compatibility of your ECU with our tech support.

DIMENSIONS:
• Product FTSPARK: 4.92 x 6.02 x 1.97 in

WEIGHT:
• Product FTSPARK-8 GEN II 750mJ: 31.22 oz
• Electrical harness FTSPARK-8 GEN II 750mJ: 56.09 oz

CONTENTS OF PACKAGING:
• 1 FTSPARK (GEN II750mJ or EXTREME) module;
• 1 installation and operation manual;
• 1 mounting hardware kit (4 rubber mounts, 8 washers and 8 nuts)

WARRANTY:
• Worldwide: 1 year

PRO550/600 FTSPARK-8 HARNESS:
The FuelTech PRO550/600 FTSpark-8 harness is a true plug and play expansion to complement both the PRO550 and PRO600 V8 harness. With this expansion harness the user can make the change to a high powered multi coil setup with ease!

The harness is fitted with a 16 way CPC firewall connection making adding the coils and FTSpark-8 a simple installation! The harness includes all terminations to suit the FuelTech CDI racing coil’s, FuelTech CAN connection and output controls. The FuelTech PRO550/600 FTSpark-8 harness has a label for each connector and the insulation is heat, moisture and oil resistant.

PRO550/600 FTSPARK-8 HARNESS SPECIFICATIONS:
• For use with our FTSPARK-8 CDI module and FuelTech CDI Racing Coils.
• FTSPARK is a high power CDI ignition module compatible with ANY ECU on the market.
Specifically designed to plug n' play with our PRO600 harness.
• If you are intending on using this harness with another ECU manufacturer, you will need to modify it and add 7 additional outputs wires.
• This harness is built using a serial bus connection (1 wire) which only works with FuelTech ECUs - FT450 and above.
• Uses Outputs B (Gray wires) on PRO600 Harness.
• Includes: CAN connector, power and ground ring terminals (battery) and 10-way Connector with wires for connection with the ECU and CPC connector for the firewall.

COILS & PLUG KITS:
• The FuelTech CDI Racing Ignition Coil is made to be used with the FuelTech FTSPARK ignition module with individual coil per cylinder and also rotary applications.
• This coil is made for Capacitive Discharge Ignition only and can not be used with a inductive ignition driver.
• Only compatible with FuelTech FTSPARK
• Not compatible with FuelTech SparkPRO

TECHNICAL DESCRIPTION
• Primary resistance: 0.09 OHM +- 10%
• Primary inductance: 0.78 mH +- 15%
• Secondary resistance: 988 ohm +- 15%
• Secondary inductance: 3.7 H +- 15%
• Leakage inductance: 0.057 mH +- 10%
• Test voltage: 470 Vdc
• Output (no load): 44 kV MIN
• Turns ratio: 70:1

COILS & PLUG KITS CONTENTS OF PACKAGING:
• 8 CDI Racing Ignition Coil
• 8 Smart Ignition Coil mating plug kit