Exhaust Gas Temperature is a critical indicator of the performance of a typical racing engine. Supercharged and turbocharged engines use EGT sensors rather than air/fuel sensors due to the volume of fuel being passed through the engine.Racepak's...

Exhaust Gas Temperature is a critical indicator of the performance of a typical racing engine. Supercharged and turbocharged engines use EGT sensors rather than air/fuel sensors due to the volume of fuel being passed through the engine.Racepak's...

These infrared sensors are used to monitor temperatures where contact cannot be made with the item being monitored. In racing, they are commonly used to monitor temperatures across the face of a tire, but they can be used for any non-contact measurement...

This replacement V-Net module is used to monitor throttle position. Designed for use with Racepak's series of travel sensors, which it connects to using a 3-pin Molex connection.

This sensor is typically used for linear measurements, such as throttle position, when the mounting angle is not critical. The sensor is calibrated to the travel of the throttle (i.e. 0% when closed and 100% at WOT). By using a string potentiometer, the...

Mount your Racepak sportsman system to your car with ease. Includes logger mounting plate, black anodized billet aluminum clamp bracket. 

Racepak's Sportsman Data Logger is designed to meet the needs of the sportsman drag racer. The Sportsman Series incorporates the same V-Net technology used by the professionals, but in an economically-priced package. In its base configuration, it can...

This connector kit provides you with the components that will allow you to repair a damaged cable or V-Net module or shorten the pigtail cable between the V-Net Module and pressure sensor.

The Racepak Switch Module provides the ability to use existing switches in conjunction with a SmartWire module. Switches are connected to the spade connectors of the Switch Module, and switch data is routed to the SmartWire via a single cable. Adding a...

This cable allows users to connect a Smartwire to their V-Net sensors and/or data logger. This cable allows the SmartWire unit to share information from your Racepak V-Net system to further enhance the switching capabilities of your SmartWire setup...

Constructed from aluminum and black anodized for a professional appearance, the SmartWire Switch Panel is connected, via a single cable, to the Switch Panel connector located on top of the SmartWire housing. Adding a second Switch Panel is quick and...

Replacement magnet used in the Racepak driveshaft collars. Also used in input shafts to register clutch RPM and on wheels to determine wheel RPM. Each magnet measures .25" OD x .20" in length. North end of magnet is painted yellow for easy...

The Racepak AF-1 is a single channel air/fuel sensor package designed to be utilized with any of Racepak’s Vnet (canbus) series of data loggers. Engineered for the harsh conditions of the racing environment, the Racepak AF-1 package includes the...

This Interface module allows users to connect shock travel sensors directly to the high speed analog port on the V300SD, V500SD and G2X Pro data loggers.Interface modules are another unique component of the V-series recorders. These black 7-pin...

This Interface module allows users to connect shock travel sensors directly to the high speed analog port on the V300SD, V500SD and G2X Pro data loggers.Interface modules are another unique component of the V-series recorders. These black 7-pin...

These linear travel sensors are designed to monitor even the slightest amount of shock travel or tire shake. These sensors can also be used to determine throttle or clutch position.

These linear travel sensors are designed to monitor even the slightest amount of shock travel or tire shake. These sensors can also be used to determine throttle or clutch position.

Zero Crossing TDC Sensor, 3-Pin 3/8" dia. This speed sensor is used to pick up Top Dead Center (TDC) on the front hub of the engine. It is designed specifically for use with MSD-style crank trigger wheel and magnets. It must be used with a RPM input...

SD / Micro SD USB Card reader. This permits the SD card to be read by a PC using the USB port rather than the SD card slot.

This single-wire sensor is commonly used to pick up fluid temperatures on the IQ3 and UDX Street Dashes and the LDX. This sensor is designed to measure the temperature of fluids such as water or engine and transmission oil where the...

The small size and ruggedness of these ‘PT-type’ pressure transducers make them ideal for the measurement of pressure directly at the source. The transducer requires 5 volt DC power and provides a .5 to 4.5 volt output signal. Each transducer...

This programming cable features a 9-pin serial connector on one end, and a 3.5MM plug which connects to the following Racepak data loggers and dashes:• Sportsman• IQ3 Display• IQ3 Logger Dash• V300SD• V500SD• G2X Length...

The small size and ruggedness of these ‘PT-type’ pressure transducers make them ideal for the measurement of pressure directly at the source. The transducer requires 5 volt DC power and provides a .5 to 4.5 volt output signal. Each transducer...

The small size and ruggedness of these ‘PT-type’ pressure transducers make them ideal for the measurement of pressure directly at the source. The transducer requires 5 volt DC power and provides a .5 to 4.5 volt output signal. Each transducer...

The small size and ruggedness of these ‘PT-type’ pressure transducers make them ideal for the measurement of pressure directly at the source. The transducer requires 5 volt DC power and provides a .5 to 4.5 volt output signal. Each transducer...

This replacement connector can repair a damaged cable, V-Net module or sensor that connects to Racepak's Molex 2-pin connectors. Includes both male and female connectors, extra pins and sockets and heatshrink.

  144" cable with Molex connector installed. Allows easy connection from the Universal Sensor Module to the following sensors:• RPM sensors• Shock travel• Ride height• Infra-red temperature• 0-5 volt

Racepak Module TD2 Block Off Plate.Limited quantities remaining. Discontinued item from Holley.All clearance item sales are final. Non-returnable.

When using the Pro Analog Transducer Box II these plug-in style transducers and signal conditioning modules are used to convert the input from various analog functions into signals that can be recognized by the recorder. Used to measure pressure...

This exposed tip Type-K thermocouple reacts quickly to changing temperatures in manifold plenum. Must be used with the appropriate thermocouple amplifier module. Probes measures 12” in length and features a...

Nut and ferrule for 1/4" EGT probes.

The IQ3 dash represents an entirely new concept in data logging dashes. By placing the 32 channel data logger, Micro SD memory card, GPS board and 3 axis G meter inside the dash, every feature of the data system is now located in one central location...

The IQ3 Display Dash can be utilized with any of Racepak's V-Net data loggers, providing a compact, fully programmable LCD digital dash for use in a variety of motorsports. Progressive shift lights, eight warning lights and all inputs are easily...

Make mounting your Racepak IQ3 dash panel an ease with this panel made of 18 gauge CR mild steel.

Mount your Racepak IQ3 dash with ease by using this sleek, trim to fit, vacuum formed plastic styled carbon fiber finish mount panel.

This sleek mounting bracket for your IQ3 dash allows for easy custom mounting within your gauge cluster area. CNC-machined, black anodized mounting bracket. Pre-drilled for corresponding IQ3 mounting stud and pattern.

This Interface module allows users to connect shock travel sensors directly to the high speed analog port on the V300SD, V500SD and G2X Pro data loggers.Interface modules are another unique component of the V-series recorders. These black 7-pin...

This Interface module allows users to connect shock travel sensors directly to the high speed analog port on the V300SD, V500SD and G2X Pro data loggers.Interface modules are another unique component of the V-series recorders. These black 7-pin...

This Interface module allows users to connect shock travel sensors directly to the high speed analog port on the V300SD, V500SD and G2X Pro data loggers.Interface modules are another unique component of the V-series recorders. These black 7-pin...

This Interface module allows users to connect shock travel sensors directly to the high speed analog port on the V300SD, V500SD and G2X Pro data loggers.Interface modules are another unique component of the V-series recorders. These black 7-pin...