Our Quarter-Max door hinge kit features mounting brackets which are longer than most of this style to offer more support to the doors when open. This kit comes with long and short mounting pins to make door removal easier. Includes all hardware needed...

Diagonal link kits are a very simple method to center the rear end.The Quarter-Max Diagonal Link Kit comes with 1" O.D. x .058" wall 4130 tube, mild steel rod ends, steel clevises with a 5/8" hole and grade 8 hardware. Welding required.For cars with a...

These are the replacement lock nuts for the QM Collector Tether System part#214514       10-32 metal to metal lock nut. This lock nut does not have nylon inside.   Sold Each   

These are the replacement primary and collector clamps for the QM Clamp On Collector Tether System part #214514. Sold Each. These replacement parts must be used in conjunction with Quarter-Max engraved collector tether system components. If you...

The Quarter-Max Clutch Linkage Kit includes a 12 in. long 4130 tube, right & left hand tube adapters, mild steel rod ends and jam nuts.For additional strength, step up to our Pro Series Clutch Linkage Kit, which uses 4340 high misalignment rod ends...

  The QUARTER-MAX® Clamp-On Tether System is NHRA accepted for the new NHRA Collector Tether rule for 2014 requiring all slip-on Header Collectors for all classes in the NHRA to be tethered. Quarter-Max® Clamp-on Tether System: Each kit...

For your convenience, we offer two styles of brake pedal push rods. The Quarter-Max Brake Pedal Push Rod (shown above) is one piece constructed from 6061-T6 Aluminum. Clevised on one end and tapped on the other, this is the easiest and quickest way to...

Wishbones are the preferred way to mount and keep the rear end housing in the center of the car. Wishbones offer more strength and less flexibility than a diagonal link.Our Quarter-Max Wishbone Kit comes complete with rod ends, housing mounts, and all...

The Quarter-Max Battery Tray is a quick, economical way to mount a single battery. Weld the tray in place and bolt the battery in place with the included  hold-down. Length: 11" Width: 7" Height: 4"

Quarter-Max's 9 in. Ford fabricated housings are available in widths of 45 in. or 60 in. and feature a 1/4 in. thick face plate drilled on a CNC mill to provide accurate stud locations. The housing covers are cut on our in-house water jet from a single...

Fabricate your own 9 in. Ford housing with our Quarter-Max fabricated housing kit. Kit includes a Quarter-Max 9 in. Ford housing face plate, banjo, inside bulkhead support, 45 in. or 60 in. short and long axle tubes, fill cap and bung, drain plug and...

Push/Pull Pin Diameter: 1/4" Length: 5/16"Sold each

Our one-piece wheel tubs are available in a variety of sizes and in either carbon fiber/fiberglass or lightweight carbon fiber (carbon/carbon). The lightweight carbon fiber wheel tubs are constructed of carbon fiber and reinforced with carbon fiber...

Our Carbon Fiber Universal Four-Piece Trunk Floor Kit makes finishing the trunk of your car quick and easy. Simply trim in various places and screw/rivet together to give you a custom fitted radiused carbon trunk floor.This item will have a discounted...

This is lightweight pure carbon fiber inner pan can be trimmed to fit your hood scoop.

This lightweight carbon fiber sheet comes in a 1 ft x 4 ft piece. It can be used to make specialty panels for your dash, ignition, or any other projects that require carbon fiber. Specifications:• Size: 1 ft x 4 ft• Thickness: .060 in.•...

Pull Pin Lanyard 3/8" x 4" Grip

Detent Pull Pin Diameter: 5/16" Length: 1"Sold each.

Detent Pull Pin Diameter: 3/8" Length: 1"Sold each.

Detent Pull Pin Diameter: 3/16" Length: 3/4"Sold each.

Detent Pull Pin Diameter: 3/16" Length: 1/2" Stainless SteelSold each.

Detent Pull Pin Diameter: 1/4" Length: 1"Sold each.

Detent Pull Pin Diameter: 1/2" Length: 1"Sold each.

This kit includes our pro series wing support kit plus brackets, struts, and hardware necessary to secure spill plates to your pro series or custom carbon wing. Includes 4 wing struts with rod ends, mounts, hitch pins, stainless steel pull pins and all...

This kit includes 4 wing struts with rod ends, mounts, hitch pins, stainless steel pull pins, and all hardware.

Includes net clip brackets, net retaining plate, and hardware to install window nets with attached push-button clips. • 4 hole style fits Stroud #505RJGA• 5 hole style fits Stroud #505RJGA-2

Our Pro Series Steering Column Kit is designed to mount easily in any chassis. Features steel tubing and an aircraft quality u-joint with sealed lubrication (for tight motor compartments or header clearance). This kit also includes a column tube with...

Constructed of 4130 Includes 2 weld-on bosses for chassis Features wraparound strap for the fuel cell and hardware Designed to mount a Jaz Pro Stock 1.5 or 2 gallon fuel cell (not included) and fuel pump (not included) Due to variations in the...

Our ultimate clutch linkage kit is used in construction of our Pro Stock cars. Kit includes 2 in. tapped link, 4340 high misalignment rod ends and jam nuts. Welding required.

The Pro Series Clutch Linkage Kit includes a 12 in. long 4130 tube, right & left-hand tube adapters, 4340 high misalignment rod ends and jam nuts. Welding required.

For a customized look and feel, try our Pro Series Brake push rod. This kit comes with a 16” long 3/4” x .058 4130 tube you cut to length, right and left hand tube adapters, and rod end. The Pro Series kit gives you smooth, consistent pedal...

Magnetically triggered switch normally open and closed with magnet passage. Same as supplied with Racepack Computer Systems. Fits 3/8" diameter hole in mount bracket.

The Electrimotion Safety Shutoff receiver for Pro Stock, Comp, Nitrous Pro Mod cars is designed to shut the car off and deploy the parachutes as the car passes the wall mounted shut off transmitter which is usually mounted 400ft beyond the...

The new generation of adjustable proportioning valves combines the latest refinements to deliver precise pressure metering and strength from a compact forged billet design. Pressure adjustments range from 100-1000 PSI and provide for a maximum decrease...

ProJack Race Car Stands is the proud designer and creator of the ProJack race car lift system which has revolutionized the method in which race teams operate today. Car owners and crew chiefs alike are insisting on using ProJack lift systems as the...

ProJack Race Car Stands is the proud designer and creator of the ProJack race car lift system which has revolutionized the method in which race teams operate today. Car owners and crew chiefs alike are insisting on using ProJack lift systems as the...

ProJack Race Car Stands is the proud designer and creator of the ProJack race car lift system which has revolutionized the method in which race teams operate today. Car owners and crew chiefs alike are insisting on using ProJack lift systems as the...

Easily store your ProJacks out of the way on the wall in your trailer or shop. Set your jacks in the pouch holder and pin the top. Jacks are stored in two separate pouches 3" deep each. 24" wide, about 7" tallest point. Black-wrinkle powder coated...

Use this replaceable Pro Jack handle on any set of Pro Jacks that will accept the threaded hub.

Weld this 4130 Chromoly bracket to your chassis for a positive lifting point for the rear ProJack lifting system. Requires two brackets per car. (welding required) Sold Each.